Low Cost, Single Use Precision Aiming Device for Explosive Ordnance Disposal Disrupters and Tools

Navy SBIR 21.1 - Topic N211-084
ONR - Office of Naval Research - Ms. Lore-Anne Ponirakis - loreanne.ponirakis@navy.mil
Opens: January 14, 2021 - Closes: February 18, 2021 (12:00pm EDT)

N211-084 TITLE: Low Cost, Single Use Precision Aiming Device for Explosive Ordnance Disposal Disrupters and Tools

RT&L FOCUS AREA(S): Autonomy; General Warfighting Requirements

TECHNOLOGY AREA(S): Battlespace Environments; Ground / Sea Vehicles

OBJECTIVE: Develop and demonstrate a low cost, single shot, precision aiming device designed to fit onto multiple Explosive Ordnance Disposal Disrupters.

DESCRIPTION: Explosive Ordnance Disposal (EOD) disrupters and tools are used to remotely open or render safe a suspect item or improvised explosive device (IED). Current precision aiming systems utilize reusable lasers that are expensive and under certain recoil forces/conditions exhibit limited survivability. The EOD community has identified the need for a low cost, lightweight, precise aiming capability for one-time use (single shot) on a variety of disrupters and tools. The aiming capability should aim and hit a variety targets with different surfaces at a standoff distance threshold of 25 feet and objective of 50 feet. It should have an aim-spot accuracy of approximately 0.955 inches (the diameter of a U.S. quarter). The capability should be able to wrap around multiple disrupter/tool barrels with a threshold requirement of 1"-2" diameters and an objective requirement of 1"-6" diameters. Separate configurations to achieve the range of 1"-6" diameters is acceptable. Battery operation of the device is acceptable. A concept of employment that provides minimal setup time with no tools is preferred along with the smallest, lightest weight configuration. Operators should be able to see the aim-spot in daylight with their eyes and remotely through a camera interface. At night, the capability should be infrared (IR) or night vision compatible. Examples of evaluations and descriptions of some DoD, local and state bomb squad disrupters and laser aiming devices are provided in References (1) and (2).

The innovation of this research is in the development of a precision aiming device that is one use, lightweight, low cost and capable of easy operator set up on multiple diameter disrupters and tools. Novel laser or non-laser solutions are acceptable.

PHASE I: Define, develop and possibly validate the initial design concept for a low cost, single shot, precision aiming device. If requested, the Government can provide an inert 155mm round fuze as an exemplar validation target. Provide a final report of the initial work and results for the single shot precision aiming device, the concept of employment for the various disrupter sizes, a device cost forecast and Phase II implementation plan.

PHASE II: Produce prototype hardware. Develop, demonstrate and validate the design. The Government can provide test opportunities on actual systems if the validation work is mature enough to enable a viable test.

PHASE III DUAL USE APPLICATIONS: Transition the device to the Joint Service Explosive Ordnance program. Manufacture a sufficient number of devices to support a statistically relevant field test validation and verification using a variety of disrupters. Additionally, the device could transition to use by state and local bomb squads.

REFERENCES:

  1. U.S. Department of Homeland Security. "Explosive Ordnance Disposal Disrupters." System Assessment and Validation for Emergency Responders (SAVER), June 2012. https://www.dhs.gov/sites/default/files/publications/EODDisrupters-SUM_0612-508.pdf
  2. U.S. Department of Homeland Security. "Laser Aiming Devices for EOD Disrupters." System Assessment and Validation for Emergency Responders (SAVER), May 2013. https://www.dhs.gov/sites/default/files/publications/LaserAimingDevices-SUM_0513-508_0.pdf

KEYWORDS: EOD; disrupter; precision; aiming; device; single-use; low-cost

** TOPIC NOTICE **

The Navy Topic above is an "unofficial" copy from the overall DoD 21.1 SBIR BAA. Please see the official DoD Topic website at rt.cto.mil/rtl-small-business-resources/sbir-sttr/ for any updates.

The DoD issued its 21.1 SBIR BAA pre-release on December 8, 2020, which opens to receive proposals on January 14, 2021, and closes February 18, 2021 at 12:00 p.m. ET.

Direct Contact with Topic Authors: During the pre-release period (Dec 8, 2020 to January 13, 2021) proposing firms have an opportunity to directly contact the Technical Point of Contact (TPOC) to ask technical questions about the specific BAA topic. Once DoD begins accepting proposals on January 14, 2021 no further direct contact between proposers and topic authors is allowed unless the Topic Author is responding to a question submitted during the Pre-release period.

SITIS Q&A System: After the pre-release period, proposers may submit written questions through SITIS (SBIR/STTR Interactive Topic Information System) at www.dodsbirsttr.mil/topics-app/, login and follow instructions. In SITIS, the questioner and respondent remain anonymous but all questions and answers are posted for general viewing. Topic Q&A will close to new questions on February 4, 2021 at 12:00 p.m. ET

Note: Questions should be limited to specific information related to improving the understanding of a particular topicís requirements. Proposing firms may not ask for advice or guidance on solution approach and you may not submit additional material to the topic author. If information provided during an exchange with the topic author is deemed necessary for proposal preparation, that information will be made available to all parties through SITIS. After the pre-release period, questions must be asked through the SITIS on-line system.

Topics Search Engine: Visit the DoD Topic Search Tool at www.dodsbirsttr.mil/topics-app/ to find topics by keyword across all DoD Components participating in this BAA.

Help: If you have general questions about DoD SBIR program, please contact the DoD SBIR Help Desk at 703-214-1333 or via email at DoDSBIRSupport@reisystems.com

[ Return ]